Brachaki Build

Page 1

Next      Home

19th September 2010

It's been a couple of months since my last build, and I figured it was time to fill some gaps.  Although I have a model of an original Met Police Box, I don't have one of the first TARDIS props, the Peter Brachaki box.  So that's my next build.  As usual the materials are 1.5mm mounting card, sticky-back plastic, and prayers, and the finished model will be about 11" high.

My initial plan was quite an exciting one, as you can see from this screenshot below. 

I was going to make a "World's End" version of the box, from the opening scenes of the first episode of William Hartnell's story "The Dalek Invasion of Earth".  In those scenes, two of the TARDIS windows on the right-hand side are tilted inwards, as in an authentic Metropolitan Police box.  I also intended to build two models in parallel, since I had found from my previous build that making two models isn't that much more difficult than making one.

Starting

Panels Done

Window thickness

Window pane

Window Tilt

 

I got so far as cutting out all 8 faces, and panelling them.  Ordinarily I only cover the blank panels, leaving the window holes open for the future windows, but in this case in order to give the window frames a bit more strength, I covered two of the faces completely, and then cut out the windows again, making them about 3mm thick.  I then cut out the required 4 windows and started considering how I was going to fit them into position.

 

 

28th September 2010

I have now revised my opinion.  Firstly I was concerned that the windows might be too flimsy, and if just one of them snapped off and fell down inside the box, I'd never retrieve it. Even if I could, I wouldn't be able to fit it back from the outside.  I considered maybe fitting a small card box round it (painted black inside) so it wouldn't fall in the box, but that might be too noticeable.  Then I actually tried gluing a section of "glass" onto a window pane, and found it was too weak.  There simply wasn't enough border to make it strong enough.

 

So I've scrapped the tilted windows idea.  Unfortunately since I now couldnt use the face I'd thickened the window sides of, I had to reuse a face from the second build, so its a single build from now on. 

 

 

25th October 2010

 

Real Life intervenes for a month, and when things settle down a bit, I continue with the build.  As usual, windows are made from plastic milk bottle, and frames are painted beforehand.  The paint is white primer undercoat, topped with Matt White Acrylic.  The roof and floor go on like a dream.  However when it comes to the first roof stack...well I'm sorry but it just doesn't look right.  I know that's how the Brachaki prop looked, but it's just too...high!  Because this stack is so deep, I build up several squares of card into a little column to support the middle.

Four Sides On

Roof On

Floor On

First Stack - Before & After

Strengthening the Stack

 

30th October 2010

 

The first stack is on, and it's time to add the corner posts.  This is different from my other builds, because the corner posts on this prop carry on past the recessed first stack.  This leaves a gap between the stack and the posts that has to be filled.  It's fiddly, but fairly easy.  I just slide a piece of card in, mark off where I need to cut it, then cut it to size and glue it in.  The post tops are a bit more difficult, but don't look too bad when completed.  As usual, painting will hide the imperfections.  The steps on this prop are quite shallow, so I use 0.6mm card.  The 2nd stack is only 5mm high on this scale model so instead of making a very shallow box, I simply cut out three squares of 1.5mm card and glue them together.  The edges are slightly uneven, but once it's painted you won't notice.

Corner Posts

Close-up Posts

Filling the Gaps

Post Tops

Steps and Second Stack

Next      Home

This Web Page Created with PageBreeze Free HTML Editor